Base:22.0. Moment of. Inertia in4:65.6 Head 2-23/32" Base 5-1/2" Shown Actual Size. 6-5/8" 3-13/16" 2-7/8" 1-1/2" R. 3-1/4" 1-11/16" 3/4" 3/8" 1/16" 1/16" R 3/4" 5/8" 1-1/8" 14" R. 3" R 10" R. 14° 02 ' 14° 02 ' 1° 26' (1:40) 14" R. 1/16" R Bolt Hole 1-1/4" 11/16" Rail Type:15 RE1. Section Number:11525. Nominal Weight:15 lbs/yd1
Brace Reinforcement Hardware - Braces and Brackets Mending plates can help reinforce, attach, connect and splice panels and other residential and industrial applications. Find corner braces, mending plates, chair corner braces, T-plates and flat corner irons here in a variety of sizes and materials. Shop Grainger for durable braces and reinforcement hardware.
Base Plate for 95 mm Rails:XT95-250:2:95 mm Construction Rail, Clear Anodized, L = 250 mm:XT95P12/M:1:Rail Plate for 95 mm Rails, 81.3 mm Long, M6 Tapped Holes:SH6MS10:1:M6 x 1.0 Stainless Steel Cap Screw, 10 mm Long, 25 Pack:W25S050:1:1/4" Washer, M6 Compatible, Stainless Steel, 100 Pack:XT95N6:1:Low-Profile T-Nut for 95 mm
Breadboard Mounting Adapters for 95 mm RailsBase Plate for 95 mm Rails:XT95-250:2:95 mm Construction Rail, Clear Anodized, L = 250 mm:XT95P12/M:1:Rail Plate for 95 mm Rails, 81.3 mm Long, M6 Tapped Holes:SH6MS10:1:M6 x 1.0 Stainless Steel Cap Screw, 10 mm Long, 25 Pack:W25S050:1:1/4" Washer, M6 Compatible, Stainless Steel, 100 Pack:XT95N6:1:Low-Profile T-Nut for 95 mm
Crane Rail :Birmingham Rail and LocomotiveStandard stock lengths 20, 30, 33 & 40 Standard Drilling 2 1/2 X 5 Joint Bars 11 lbs (with hardware) Bolt 3/4 diameter. Standard Fasteners
J & J Rail Sales stocks a large inventory of ASCE Crane Rail, and all Crane Rail is stored inside to keep rust to a minimum. 12# 20# 25# 30# 40# 60# 80# 85# 104# 105# 135# 171# 175# Call Us Today for a Free Estimate. Or click below and get your quote online. Wheel Quote Form; Rail Quote Form
J & J Rail Sales Crane RailJ & J Rail Sales stocks a large inventory of ASCE Crane Rail, and all Crane Rail is stored inside to keep rust to a minimum. 12# 20# 25# 30# 40# 60# 80# 85# 104# 105# 135# 171# 175# Call Us Today for a Free Estimate. Or click below and get your quote online. Wheel Quote Form; Rail Quote Form
Kimes Steel & Rail, Inc.About Kimes Steel & Rail, Inc. Employment Application. Address:2 George Street, New Haven, WV 25265. Mailing Address:PO Box 330, New Haven, WV 25265
RAIL SALES TERRITORY MAP. Transit Agencies / Design Consulting Firms. Class 1's / Contractors / Industrials / Regionals & Shortlines Friction Management Field Services. Jim Tanner Director of Rail Business Field Services Phone:412-928-7888 Email:[email protected] 415 Holiday Drive, Suite 100 Pittsburgh, PA 15220. Debbi Lowry Field Service
Light Post Base Design - Structural engineering general May 05, 2008 · The catalogue will also have a base detail with anchor bolts (number and sizes) for every pole. You can either design for the capacity of the anchor bolts (conservative) or apply the EPA at some conservative height (not all the way at the top), use the wind load from ASCE 7, and design for that.
Practical Design and Detailing of Steel Column Base PlatesSteel column base plates are one of the most ~ndamental parts of a steel structure, yet the design of base plates is commonly not given the attention that it should by engineers. This results in base plate details that are expensive, difficult to fabricate and may even contribute to the hazards
Stainless Steel:ASCE 8. c. Provide formed steel brackets with predrilled hole for bolted anchorage and with snap-on cover that matches rail finish and conceals bracket base and bolt head. d. Provide brackets with interlocking pieces that conceal anchorage. Locate set screws on
STRUCTURE magazine Base Plate Design for Post-Installed The term base plate is commonly understood as referencing a steel plate placed beneath a column to distribute applied loads to a concrete member. The plate is assumed to act as a cantilever beam fixed at the edges of the column, defined by the geometry of a structural profile (Figure 1). If a wide-flange section is used as a column, the base
Steel Bolt Edge Distance Requirements - Engineering E®Per AISC-ANSI-360-10, the minimum edge distance for bolts is to follow the below table J3.4
304 Sheet & Plate; 304 Perforated; 316 Sheet & Plate; Stainless Steel Tube. 304 Round; 316 Round; 304 Square; 304 Rectangle; Stainless Steel Pipe. 304 Pipe; Stainless Steel Angle. 304 and 316 Angle; Copper / Brass. Copper Bar. 110 Rectangle; 110 Round; Copper Sheet & Plate. 110 Sheet & Plate; 110 Foil; Brass Bar. 360 Round; 360 Hex; 360 Square
Version 14 - American Institute of Steel ConstructionDesign Examples V14.0 AMERICAN INSTITUTE OF STEEL CONSTRUCTION iii PREFACE The primary objective of these design examples is to provide illustrations of the use of the 2010 AISC Specification for Structural Steel Buildings (ANSI/AISC 360-10) and the 14th Edition of the AISC Steel Construction Manual. The design examples provide coverage of all applicable limit states whether or
steel rail asce 75, steel rail asce 75 Suppliers and A wide variety of steel rail asce 75 options are available to you, such as aisi, astm, and jis. You can also choose from non-secondary steel rail asce 75, as well as from railway rail, guide rail steel rail asce 75, and whether steel rail asce 75 is heavy rail, or light rail.
20 length 12.0 Ibs. per pair Bolt diameter 3/4 Full toe and toeless bars also available. Rail - Section 60AS 60 Ibs. per yard 105.6 net tons per mile of track 50 feet of track per net ton Stock lengths 30, 33, 39 & 40 Splice Bars 20 length 24.2 Ibs. per pair Bolt diameter 3/4